Emulsion & Haze Removers

Sten-X Stencil Remover is a "ready for use" emulsion remover. Sten-X quickly breaks down emulsion for fast efficient screen reclamation. Biodegradable and VOC free Sten-X is perfect for printers who do not want to make their own emulsion removers. -Ready to use, regular strength emulsion remover -Has superior wetting prperties -No precipitation of active ingredients

Ready-to-use stencil liquid remover for fast and thorough removal of direct emulsions, CDF Direct-Films, and Pulsar indirect film from all types of mesh including metalized polyester. Will not etch mesh; contains no strong alkalis or hypochlorites. Ideal for use in tanks: will not attack adhesives on stretch and glue frames; tank heating unnecessary. Odor free Instructions -Remove ink with the proper solvent. -Use Screen Degreaser Liquid No. 3 to remove solvent residues and to help speed the action of the stencil remover. Rinse thoroughly. -Use a soft brush to apply Stencil Remover Liquid No. 4 on the screen from both sides. -Wait five minutes - no longer. Do not allow the stencil remover to dry on the screen, as this can result in a permanent stencil. -Wash away the stencil with a hard spray of water, preferably a power spray. -Tank method: Dilute Stencil Remover No. 4 with water (no more than 1:2) - but only after thorough testing. It is recommended, however, that Ulano No. 4 be used at full strength for fastest and most thorough stencil removal. Health & Safety Information Stencil Remover Liquid No. 4 is a strong oxidant. It can cause skin irritation; use gloves. Keep the container closed tightly. Clean spills immediately. First Aid: In case of contact with the eyes or skin, flush immediately with water. If irritation develops, contact a physician.

A liquid haze remover that is very effective on inks and emulsions. Non-caustic. Haze Free is a powerful haze and ghost remover that works quickly to dissolve ink and residual emulsion stains from all types of mesh. Drain safe and biodegradable, Haze Free is the most effective Haze Remover on the market. Specifically formulated to remove imbedded U.V. and plastisol inks (haze and ghost images) that remain on the screen. -Emulsifies and dissolves the ink constituents; resins, binders, pigments, plasticizers, etc. -The solution suspends these constituents so re-attachment to the mesh surface is prohibited, thus allowing for water rinse removal. -Excellent degreaser, as it also removes dirt, residues and sizing.

Ready-to-use paste for fast and thorough removal of direct emulsions, CDF Direct Films, and Pulsar indirect film from all types of mesh including metalized polyester. Instructions -Remove ink with the proper solvent. -Degrease first with Screen Degreaser Liquid No. 3 to remove solvent residues and to help speed the action of the stencil remover. Rinse thoroughly. -Use a soft brush to apply Stencil Remover Paste No. 5 on the mesh from both sides. -Wait five minutes - no longer. Do not allow the stencil remover to dry on the screen, as this can result in a permanent stencil. -Wash away the stencil with a hard spray of water, preferably a power spray. Note: Avoid freezing Stencil Remover Paste No. 5. Freezing and thawing will change the consistency from a paste to a liquid. This has no effect on the chemical activity as a stencil remover - it can be used in the same way as Stencil Remover Liquid No. 4. Health & Safety Information Stencil Remover Paste No. 5 is a strong oxidant. It can cause skin irritation; use gloves. Keep the container closed tightly. Clean spills immediately. First Aid: In case of contact with the eyes or skin, flush immediately with water. If irritation develops, contact a physician.

An ink haze and stencil residue remover that is effective on most inks and emulsions. The efficiency depends on the age of the dried-in ink. Haze Remover Paste No. 78 does etch mesh surfaces. To avoid premature rupture of your mesh, (especially worn or fine mesh), it is best to limit the application time to as short as necessary and never more than 10 minutes. Wear goggles and gloves. Follow instructions carefully to avoid damaging mesh. Recommended for use with all Ulano Stencil systems on all mesh except natural silk and metalized polyester. For industrial use only. Very low alkaline content. Instructions -Power wash after rinsing most of the haze remover from the mesh -Remove ink and stencil as usual and allow the mesh to dry. -Stir the Haze Remover Paste No. 78 thoroughly. -Results can be improved if the mesh is treated with the solvent of the ink before the paste is applied. -Water on the screen or brush dilutes the action of the chemical. -Brush the paste briskly on both sides of the dry screen with a dry, long bristle nylon brush. -Haze Remover Paste No. 78 does etch mesh surfaces. To avoid premature rupture of the mesh, especially worn or fine mesh, it is best to limit the application time to as short as necessary. -Let the screen stand for no more than ten minutes or the paste can damage the mesh. -Never let No. 78 dry on the mesh. -Rinse with a gentle spray to avoid splashing the chemical, then a power spray from both sides. Health & Safety Information Haze Remover Paste No. 78 is for industrial use only. Use adequate ventilation. Avoid prolonged breathing of vapors. Avoid contact with the skin, eyes, mucous membranes, and clothing. Haze Remover Paste No. 78 is combustible: do not use near heat or open flame. It is corrosive and contains caustic soda, causing severe burns on contact. Harmful or fatal if swallowed. Flush spills immediately with water mixed with equal parts of vinegar. Wear rubber gloves, goggles (or preferably a plastic face mask), and a plastic or rubber apron. First Aid: Eyes - Flush immediately with water for at least 20 minutes. External - Flood exposed area with water for at least 15 minutes. Wash with a solution of equal parts vinegar and water. Internal - Drink large quantities of water or milk followed by citrus juice or diluted vinegar. Do not induce vomiting. CALL A PHYSICIAN AT ONCE. UPS or FedX Hazardous Fee